BERNSTEIN, ESD TOOL KIT TECHNICLINE VARIO 6 PCS (INCL. ESD TOOL HOLDER)

• content: article listing see below
• Full Flush (without side face, cut completely flush)
• side cutters cutting capacity soft/medium/hard/piano Ø in mm: 1.0/0.8/0/0
• end cutters cutting capacity soft/medium/hard/piano Ø in mm: 0.8/0.6/0/0
• head width approx.10 mm, blade length 8 mm
• material ball bearing steel (HRC 63-65), selected models available as hard metal side cutter (HRC 81) for hard wires on request
• surface without reflection matt polished
• dissipative between 10^6 and 10^9 ohm
• measures 150 x 190 x 80 mm

AREA OF APPLICATION

TECHNICline precision pliers set with ESD tweezers are suitable for mobile work, for service employees, as well as for stationary work on ESD workstations or for EPA (Electrostatic Protected Area). The pliers are suitable for cutting general resistance wire, solder wire, winding wire and heating wire (thermocouple wire). Specifically for copper wire, brass wire, steel wire, iron wire, aluminum wire, bonding wire, tin wire, nickel wire, gold wire, silver wire, platinum wire, tungsten copper wire, tungsten wire, glass fiber and kevlar. Please note the cutting capacity in the pliers handles and the care instructions for a longlife of your pliers. For special applications and individual solutions, please contact us, we are pleased to advise you. The practical VARIO tool holder is made of sturdy 1.5 mm sheet steel and has a high-quality dissipative black powder coating. In addition to pliers and tweezers, our handy screwdrivers or round objects with a maximum diameter of 9 mm can also be stored. The recess in the lower area allows the blades or tips of the tools to be quickly identified and selected. The locking aid at the rear edge additionally helps to hold each tool in position. Small noses on the upper edge of the suspension rail prevent pliers or tweezers from slipping down. The tool holder can be set up as well as hung. Two holes on the back allow easy mounting on the wall.

TECHNICAL DESCRIPTION

CARE NOTE: High humidity or touching the pliers head with your fingers (sweat) causes rusting. Therefore, the pliers should always be kept dry or protect with oil for storage. If there is any rust on the pliers head, it can be easily removed, with a slight polish. Our ESD tools comply with the following ESD standards DIN EN 61340-5-1; VDE 0300-5-1:2017-07; DIN EN 61340-2-1; VDE 0300-2-1:2016-07; DIN EN 61340-4-6; VDE 0300-4-6:2016-04. We achieve a discharge resistance of 10^6 to 10^9 ohm with the pliers handles, the ESD tweezers and the tool holder. Attention, the use of hand tools alone is not enough to avoid electrostatic charge. For general safety, please use our wrist grounding and ESD mats, for further information see the section workplace equipment.

GENERAL INFORMATION

The TECHNICline pliers series is made of high-quality ball bearing steel with exceptional cutting performance for extremely high requirements and demands. The pliers are scratch-resistant, matt-polished, reflection-free and glare-free for optimal work under the magnifying glass or the microscope. The exact symmetrical, induction-hardened cutting edges have a hardness of 63-65 HRC and thus achieve particularly high cutting values. These stable cutting edges are suitable for a wide variety of hard wires. If required, HRC 81 is also available as a hard metal cutter made of tungsten carbide steel, only for selected models - on request). The screwed precision joint with hardened nut (made of alloy steel) ensures perfect joint adjustment and durability even with high cutting loads. Ergonomically shaped, dissipative 2-component hand covers offer a pleasant feel and optimal relief of the hand muscles thanks to the stainless steel double leaf spring.